The History of
Weather-Bos™

Why use Weather-Bos™?

Comparisons

Customer Testimonials

Uses for Weather-Bos™ (i.e. roofs, sidings, fences)

Industries using
Weather-Bos™ (i.e. architects, contractors, wood product
manufacturers)

Truth vs.Confusion

Spec and Technical Data

The advantages of Pre-
Staining your wood

How Much Weather-Bos™
do I Need?

Why does wood turn grey
and dull?

The science behind the
stains which occur on wood
.

How to Become a
Weather-Bos™ Distributor/Manufacturer

Weather-Bos™ Seminars

Frequently Asked Questions

Free Orderline 1-800-664-3978

SIMPLE DIRECTIONS FOR ROOF BOSS™
  • Pressure wash entire roof using a minimum of 3000 PSI with a 25° spray tip.
  • Carefully inspect roof, replacing shakes or shingles as required.
  • Rinse entire roof with pressure washer.
  • Paint all valley and roof metal.
  • Air blow roof, including gutters.
  • Carefully clean surrounding surfaces; i.e., gutters, windows and door frames of any dirt or residue.
  • Apply flood coats of the correct Weather-Bos™ formula to the prepared roof surface using an airless or low pressure sprayer.
  • To obtain maximum protection, a minimum of two applications is recommended.

TILE/SLATE

  • Wash surface with pressure washer or any agreeable method, being careful not to damage roofing material.
  • Tile must be clean and dry, then in direct sunlight or high heat, apply multiple light coats with airless or low pressure sprayer.
  • It is extremely important to allow adequate drying time between applications.
  • Do not apply if rain is likely to occur soon after applications.
  • To obtain maximum protection, a minimum of three applications is recommended.

COMPOSITION/FIBERGLASS

  • Wash and clean surface by any agreeable method, being careful not to damage roofing material.
  • Surface must be clean and dry, then apply multiple light coats in direct sunlight or high heat, with airless or low pressure sprayer, allowing adequate drying time between applications.
  • To obtain maximum protection, a minimum of two applications is recommended.
  • Do not apply if rain is likely to occur soon after applications.

WOOD

  • Pressure wash entire roof using a minimum of 3000 PSI with a 25° spray tip.
  • Carefully inspect roof, replacing shakes or shingles as required.
  • Rinse entire roof with pressure washer.
  • Paint all valley and roof metal.
  • Air blow roof, including gutters.
  • Carefully clean surrounding surfaces? gutters, windows and door frames of any dirt or residue.
  • Apply flood coats of the correct Weather-Bos™ formula to the prepared roof surface using an airless or  low pressure sprayer.
  • To obtain maximum protection, a minimum of two applications is recommended.

CLEAN UP

  • Clean hands and tools with soap and water.

MAINTENANCE

  • To retain a quality appearance the surface should be cleaned by any agreeable method.
  • Apply additional Roof Boss™ as necessary. A high degree of protection will remain, regardless of appearance, due to previous applications of Roof Boss™ that have bonded with the roofing material.

COVERAGE:

Weather-Bos™ products will have an average coverage between 50 to 100 sq. ft. (4.7-9.3 sq. ms.) per U.S. gal. on each application depending upon surface and conditions.

If swallowed, drink milk or warm water, induce vomiting and call a physician.

This product complies with all California and Federal V.O.C. limitations.

 



Repair & replace damaged wood



Pressure wash entire surface
Click on the bar below to find out more information about our six fantastic formulas!!!


Apply formula by spraying


Finished roof
CLICK ON THE SUN TO REQUEST FURTHER INFORMATION
Home Frequently Asked Questions Uses Product Information Business Opportunity Search Purchasing Environmental Issues

©1996-2005 Weather-Bos™ International. All Rights Reserved. Website Design by Hinman Associates.